Coffee Bar Builders

Guide · Homeowners · 4 min read · Updated 17 November 2026

Home Coffee Station Planning Checklist: Space, Power and Storage

Short answer

Before building a home coffee station, measure your machine and grinder with the lids and portafilter in place, allow at least 600 mm of worktop width for each, plan sockets for every appliance, leave space above for heat and tank access, and choose a position away from the hob but near water if the machine is plumb-in. Storage for cups, beans and tools completes the plan.

Home Coffee Station Planning Checklist: Space, Power and Storage

Choose the right position

The best spot is out of the main cooking zone but close enough to the kitchen to share water and drainage. Alcoves beside a chimney breast, the end of a kitchen run, a utility room doorway or an under-stairs cupboard all work well. Avoid placing a coffee station directly beside the hob, where grease and steam settle on the machine, or beside the fridge, where heat from the machine can affect the fridge's efficiency.

Think about how people move. A coffee station on the route between the kettle and the dishwasher can become a bottleneck at breakfast. In an open-plan room, a station on the dining side lets guests help themselves without walking into the cooking area.

If your machine is plumb-in, the nearest cold supply and drain will strongly influence the position. Under-stairs spaces next to a kitchen wall are often ideal because pipes can run a short distance through the wall rather than across the room.

Measure the kit, not the catalogue

Measure the machine, grinder and any milk fridge or water boiler you plan to use. Include the height with the bean hopper fitted, the depth with the portafilter or drip tray in place, and the clearance needed to lift the water tank lid. A common mistake is building a shelf above the machine that blocks the tank or hopper, forcing you to pull the machine forward every time.

The table gives typical space needs. Your own kit will vary, so confirm with actual measurements before the joiner cuts anything.

ItemTypical width allowanceClearance to plan
Domestic espresso machine300–450 mmSpace above to lift the tank lid and warm cups
Bean-to-cup machine250–400 mmRoom to slide out for cleaning and refilling
Grinder150–250 mmFull hopper height plus room to lift it off
Knock box and tools150–200 mmDrawer or tray below the machine
Under-counter milk fridgeAround 600 mmVentilation gaps to the manufacturer's spec

Power and lighting

Every appliance needs a socket, and ideally a spare one for a milk frother or kettle. Domestic espresso machines can draw close to the maximum a standard plug allows, so avoid running a machine, kettle and toaster through an extension lead. Sockets are best placed above the worktop and to one side of the machine, not hidden directly behind it, so you can unplug for cleaning.

If the station needs new sockets, the electrician will check whether they can come from an existing circuit or need a new one. New circuits in homes in England and Wales are notifiable under Part P of the Building Regulations unless done by a registered competent person, and all work should meet BS 7671. LED strip lights under shelves or inside a tall cabinet make the station easier to use early in the morning.

  • At least one double socket per pair of appliances
  • Sockets above the worktop, beside rather than behind the machine
  • A switched LED lighting circuit for shelves or cabinet interior
  • USB or a spare socket for a frother or scales
  • No extension leads carrying high-power appliances

Ventilation and heat

Coffee machines release heat and, during steaming, a fair amount of moisture. In an open alcove that is rarely a problem. In a tall cupboard station with doors, the machine needs breathing space while it runs, so pocket doors that retract fully into the sides are popular. Some joiners add a discreet vent slot at the top of the cabinet, and the shelf above the machine is often finished in a material that copes with warmth and occasional steam.

Integrated coffee machines, designed to sit in a tall housing alongside ovens, have specific ventilation and cut-out requirements set by the manufacturer. Following those dimensions exactly avoids overheating and keeps the appliance warranty valid.

A quick planning checklist

Before you ask for a quote, run through the essentials so the joiner can design the station properly from the first visit. Having this information ready also means the price you receive is accurate rather than an estimate that changes once work starts. Photos of the space, with a tape measure visible, are a useful addition to any quote request.

  • Make and model of the machine, grinder and any fridge
  • Measurements of each appliance including lids and handles
  • Width, depth and height of the alcove or space
  • Whether the machine is tank-fed or plumb-in
  • Number and position of sockets needed
  • Door style: open, hinged, bi-fold or pocket doors
  • Worktop material and whether it must match the kitchen
  • Storage needs for cups, beans, pods and accessories
  • Lighting: under-shelf strips or cabinet interior lights

Storage that earns its keep

Plan storage around your daily routine. A shallow drawer under the machine holds tampers, cloths, milk jugs and cleaning tablets. A deeper drawer can house a built-in knock box with a cut-out in the worktop. Open shelves above display cups and keep them warm, while a closed cupboard hides bags of beans, syrups and filters. If you use pods, a dedicated pull-out tray keeps them organised.

Finally, think about the worktop surface. Hot drips, coffee grounds and milk splashes are constant, so pick a surface that wipes clean and resists heat. We arrange coffee stations through vetted local joiners and electricians, who will measure your kit and room before giving a fixed price.

Questions people also ask

How deep should a coffee station worktop be?

Standard kitchen worktops are 600 mm deep, which suits most domestic machines. Larger dual boiler or commercial-style machines may need 650 mm or more so the machine sits back from the edge with room for the portafilter. Alcoves are often shallower, so measure the recess and the machine before choosing.

Can I put shelves above my coffee machine?

Yes, but leave enough space to lift the water tank lid and refill the bean hopper, and allow for heat rising from the machine. A gap of at least the machine's top clearance, typically 300 mm or more, is sensible. Check the machine manual for any stated clearance.

Where should a coffee bar go in the kitchen?

Ideally away from the hob and fridge, near a socket and, for plumb-in machines, close to the water supply. Alcoves, the end of a run of units and under-stairs spaces work well. In open-plan rooms, putting it on the dining side keeps people out of the cooking area.

Written and checked by the Coffee Bar Builders team. Read our editorial policy.

Get a free coffee bar builders quote

Tell us what you need and we'll come back with a clear price.

Request a quote